8 Reasons Why Toilet Seat Won’t Stay Up

Many people complain that toilet seats do not stay up and slam down frequently on the bowl. The sudden slamming can increase the risk of injury and disturb the people sleeping in the connected bedroom.

Toilet seat won’t stay up because of no distance between seats and cisterns, loose screws, installation in high traffic areas, poor installation of screws, incorrect opening and closing, thin lids, blockage at their moving end, wobbly cistern, and installation on a poorly leveled surface.

It is necessary to fix the problem because it is annoying and disturbing for people when they suddenly hear uneven sounds from the bathroom. In addition, it is risky for your kids and pets because they can get injured from their unusual movements.

Reasons Solutions
No distance between seats and cisterns Move the seats slightly forward
Loose screws Tighten screws with pliers
Installations in high-traffic areas Proper inspection and maintenance
Incorrect opening and closing Don’t open and close them harshly
Covered ends and thin lids Avoid using heavy toilet seat covers
Blockage and warping of plastic material Lubricate hinges
Wobbly cisterns Add thick foam
Adjustment on a poorly leveled surface Install shims

No distance between seats and cisterns

The toilet seats do not stay up when there is minimum and no distance between them and cisterns. Therefore, the proper angle between these two components should be 90 degrees.

The covers do not have sufficient space for their opening. In addition, the water tank is causing hindrances in their proper opening, which come down when you sit on them.

In addition, the issue comes when these are installed close to the water tank and cannot rest there because of insufficient space.

Loose the screws that are attached to the lid and pull the seats forward according to the required space. Check their proper opening and closing before tightening the screws.

Tighten the screws if you see these do not come down when you open the lid.

Loose screws

The screws are attached to the lower side of the seats to connect them to the toilet bowl properly. The screws because loose because of daily use and when you do not fasten them properly.

The loose screws cannot hold them in their place, and these come down frequently. The issue comes from the regular excessive weight on them.

These are made of metal material, and rust can come on them from exposure to water splashes. The rust can reduce the strength of metal screws and make them flexible and easily breakable.

Replacement of screws is better to avoid corrosion on their surface. Replace the metal screws with plastic ones because these are resistant to rust.

Use the screwdriver to remove the old screws and installation of new ones.

Installations in high-traffic areas

Sometimes the toilets are installed in high-traffic areas, and excessive use increases the risk of damage. The screws and hinges become loose when you open and close them frequently.

The problem comes when children use them frequently as a fun activity. In addition, the toilets that are present on the ground floor have more issues like these because of their excessive usage.

Proper inspection of toilets installed in high-traffic areas of your home increases their longevity and protects them from damage.

Tighten their nuts using the screw wrench or pliers and check them routinely.

Incorrect opening and closing

The seats of your bathroom toilet come down suddenly due to poor handling and incorrect use. Many people use them harshly and put pressure on them.

The harsh opening and closing can damage their screws and make them loose. In addition, it also causes the displacement of screws from the installation size, and these cannot hold the lid in its specific position.

Children often treat these parts harshly and suddenly slam the seat covers down after using them. Instead, handle them properly and reduce the risk of damages and repair costs.

Properly put them on the bowls when you use the toilets instead of shutting them down suddenly.

Covered ends and thin lids

Many people install the covers on the toilet seat for the designing purpose and to avoid spillages of water. In addition, the covers also insulate their cold surfaces, and you can easily use them in winter.

The covered ends increase their weight and decrease the distance between them and the water tank. In addition, the thin covers bound the space present for their proper opening and maintain their angle.

These cannot rest there and comes down when you open them. Moreover, the problem comes when lids are thin and won’t stay up.

The little air pressure and force can cause them to come into the bowl. Use the correct size of lids for their better functioning.

Avoid using heavy and fabric-type seat covers for your toilets because these can cover the distance and add weight.

Blockage and warping of plastic material

The issue comes when there is a blockage in the hinges, which decreases their holding power. Sometimes the little foreign particles get stuck in the inner side and cause hindrance in the opening and closing of the toilet seat.

These cannot open properly because of blocked hinges and comes down. The blockage occurs when a rust layer is built on metal hinges.

In addition, other small objects like hairpins and beads from your cloth also get stuck in them and disturb their functioning.

Loosen the hinges and screws that are present on the joining ends of the seat covers or lid to check blockages. Remove the foreign particle or dust accumulated in them for their smooth functioning.

Clean the rust and lubricate it with high-quality lubricant for its smooth functioning.

Wobbly cisterns

The wobbly cisterns or water tanks cause the toilet seat to come on the bowl. It pushes the lids forward because these are heavy.

The cisterns become wobbly because of their poor adjustment and installation. In addition, the screws connecting the cisterns to the toilet boil become loose and cause the issue.

In addition, the problem also comes when these become old and their mounting screws wear out. The screws become faulty with their age because of the constant weight of water on them.

Tighten the screws or install new ones if they are loose or broken. Add the thick foam on the tank’s backside if the problem is poor installation.

Adjustment on a poorly leveled surface

The toilet seat frequently comes down in your bathroom because of their poor installation. Sometimes these are not installed on the leveled surface of the floor.

The poor and incorrect leveling does not allow the lid to stay up. The issue comes when these are installed in an inclined position from the bowl side.

The redirecting forces cause their frequent closing and produce sudden shutdown sounds. The problem comes when you install them at home and from the negligence of plumbers.

The wooden floors often become uneven due to damage to wooden material. Using the shims on the lower side of the toilets is better to provide better support and adjust the angle.

Calling a plumber to install shims is suitable because sometimes you have to remove the toilets for them.

Related Articles:

Toilet swirls but won’t flush

What Happens If You Don’t Flush a Toilet For Months?

Flush Cigarettes in Toilet